FRS/GMRS/MURS/CB: The Personal Radio Services

Anyone can use one of several types of two-way radios, most of which do not require a license. From something the kids can play with to serious business uses there are a bunch of different types of varying quality and usefulness. These are called CB, FRS, MURS and GMRS. Only GMRS requires a license, the others do not. Each of the four services have different intended functions.

  • FRS: Family Radio Service (low power, short range, intended for families and individuals)
  • GMRS: General Mobile Radio Service (high power, longer range, intended for families)
  • MURS: Multiple Use Radio Service (mid-power, medium range, intended for business)
  • CB: Citizen’s Band Radio Service (low power mobile)

You ever go into Wal-Mart or Best Buy and see those cheap little two-way radios encased in one of the most devious inventions of man-kind (Bubble Packs)? They boast wild range figures (“35 mile Range!”) and are made by many different companies like Motorola, Midland and Cobra. These are called “FRS Radios” (Family Radio Service). FRS radios are restricted to ½ watt, non-removable antennas and are intended for short-range person-to-person communications. While titled as the Family Radio Service they are commonly used by businesses and government organizations. In my neighborhood I hear construction crews, hunters, the local school and the golf course maintainers on FRS channels. Just about everything but families… There are few restrictions on what you can use it for so business and personal communications are allowed.

FRS is actually pretty interesting to listen to in many cases. While a lot of the traffic is inane nonsense, like kids wearing out the noisemaking alert beep button, occasionally there is some interesting stuff to listen to. I live in a fairly isolated area 20 miles from the nearest town. There is construction going on and the crews use several FRS channels to coordinate activities. There is a school in the area that uses FRS radios too. The golf course guys use FRS when performing maintenance or to corral loose duffers. Local landscapers use FRS as well.

Listening to FRS channels at the mall or around amusement parks etc. can also be fun. The stores and shops often use FRS radios for clerks and stockers, customers use them to keep in touch with their family.

A lot of the FRS channels are shared with GMRS, so listening to one set of frequencies you may hear both services.

GMRS is a little different than FRS. Since a license is required and power levels are higher they tend to be used in a more formal matter. FRS also allows repeaters so you may hear traffic from all over the area. GMRS is often used by REACT and other volunteers as well as family businesses and often for just idle chit-chat and radio clubs. Sometimes it sounds a lot like ham radio.

MURS can be very interesting. It is on VHF and allows higher power than FRS but in many other aspects it is very similar. Like FRS there are few restrictions on what you can use it for. Since the radios tend to be a little more expensive MURS channels tend to be more business oriented.

CB these days is mostly a wasteland of unintelligible noise. It is still popular with the highway crowd but between high-power illegal amplifiers, over-driven power echo-mics and other noisemakers it is no longer a viable communications tool. It can be interesting to listen to however!

If you put these frequencies in your scanner you may find some interesting communications. You might also be bored silly but you won’t know until you try it.

General Mobile Radio Service (GMRS)

  • Freq (MHz)              Remarks                  
  • 462.5500                 Repeater Output/Simplex    (Repeats 467.5500)
  • 462.5750                 Repeater Output/Simplex    (Repeats 467.5750)
  • 462.6000                 Repeater Output/Simplex    (Repeats 467.6000)
  • 462.6250                 Repeater Output/Simplex    (Repeats 467.6250)
  • 462.6500                 Repeater Output/Simplex    (Repeats 467.6500)
  • 462.6750                 Repeater Output/Simplex    (Repeats 467.6750)
  • 462.7000                 Repeater Output/Simplex    (Repeats 467.7000)
  • 462.7250                 Repeater Output/Simplex    (Repeats 467.7250)
  • 462.5625                 Simplex (5 watts)
  • 462.5875                 Simplex (5 watts)
  • 462.6125                 Simplex (5 watts)
  • 462.6375                 Simplex (5 watts)
  • 462.6625                 Simplex (5 watts)
  • 462.6875                 Simplex (5 watts)
  • 462.7125                 Simplex (5 watts)

Family Radio Service (FRS)

  • Freq (MHz)              Ch #         
  • 462.5625                 1
  • 462.5875                 2
  • 462.6125                 3
  • 462.6375                 4
  • 462.6625                 5
  • 462.6875                 6
  • 462.7125                 7
  • 467.5625                 8
  • 467.5875                 9
  • 467.6125                 10
  • 467.6375                 11
  • 467.6625                 12
  • 467.6875                 13
  • 467.7125                 14
  • 462.5500                 15 (Shared with GMRS)
  • 462.5750                 16 (Shared with GMRS)
  • 462.6000                 17 (Shared with GMRS)
  • 462.6250                 18 (Shared with GMRS)
  • 462.6500                 19 (Shared with GMRS)
  • 462.6750                 20 (Shared with GMRS)
  • 462.7000                 21 (Shared with GMRS)
  • 462.7250                 22 (Shared with GMRS)

Multiple Use Radio Service (MURS)

  • Freq (MHz)                                                 
  • 151.8200
  • 151.8800
  • 151.9400
  • 154.5700
  • 154.6000

Citizens Band (CB)           

  • Freq         Ch #          Freq         Ch #         
  • 26.965    1                27.215    21
  • 26.975    2                27.225    22
  • 26.985    3                27.255    23
  • 27.005    4                27.235    24
  • 27.015    5                27.245    25
  • 27.025    6                27.265    26
  • 27.035    7                27.275    27
  • 27.055    8                27.285    28
  • 27.065    9                27.295    29
  • 27.075    10             27.305    30
  • 27.085    11             27.315    31
  • 27.105    12             27.325    32
  • 27.115    13             27.335    33
  • 27.125    14             27.345    34
  • 27.135    15             27.355    35
  • 27.155    16             27.365    36
  • 27.165    17             27.375    37
  • 27.175    18             27.385    38
  • 27.185    19             27.395    39
  • 27.205    20             27.405    40

WiFi on BCD536HP. How does it work?  What you can and can’t do with it.

The Uniden Bearcat BCD536HP is the only scanner that has the capability of being directly controlled by WiFi. By using the included WiFi dongle one can connect a smart phone or tablet to the scanner and listen to and control the scanner with the device. There are some other uses for the WiFi dongle as well.

Uniden has provided free “Siren” software (available for free via the Apple iTunes store or Google Play Store) to allow you to use your smart device as a scanner controller. You can even use this as a remote head for the scanner if mounted in a vehicle or to listen to your scanner from the patio or another room of the house for a scanner installed in the home. Some third party software allows you to use the WiFi feature to connect the canner to the computer without the need to plug in a cable.

There are a few things that the WiFi dongle will not work for, this includes database and firmware updates and other programming.

The Wifi dongle is designed specifically to work with your home or office WiFi network. While we have read of people using it for remote access this requires such networking tools as VPN, if you know how that works you probably can figure it out. Sorry, we cannot help with notworking issues like this!

To use the WiFi feature you need to understand the two modes involved; Infrastructure and Access Point.

Infrastructure Mode allows your scanner to connect to your home or office WiFi. This then allows you to connect to the scanner via third-party software like ProScan or RadioFeed or to the Siren application.

To get to Infrastructure Mode use the following steps:

Press Menu then select WiFi Setup>Select WiFI Mode>Infrastructure Mode

The radio will look for local access points and list them. When it displays the list select your router’s SSID name.

Then enter your password for the WiFi access point. This is the same password you would use for setting up any other WiFi device on your network. To enter the password you scroll thru the letters and use the 4 and 6 buttons to move the curser.

Access Point Mode allows you to connect you scanner to a smart phone or tablet (iOS or Android) using the free Siren software. You would use this when you are not in range of your WiFi system, such as when the radio is mounted in a vehicle. This allows you to use a phone or tablet as sort of a remote control head for the scanner.

In Access Point Mode the 536 acts as an Access Point and provides an SSID which you can change or leave at the default. You then connect your phone or tablet to that WiFi SSID and enter in the IP address in the Settings of the device. The IP address can be found in the WiFi settings on the scanner.

Siren is the free app available at the Apple iTunes Store for iPhones, iPads and iPod Touch’s. It is also available for Android devices at the Google Play Store.

Siren is a neat way to use your 536 scanner but there are limits to it. It will only work with the 536, and it has limited abilities for control. It can set the range, select Quick Keys, set the squelch and start and reply the recording features but that is pretty much all she wrote. There is also a 2-3 second delay in hearing the audio compared to the radio itself.

The WiFi feature on the 546 is unique and useful as long as you know its limits.

VLog – Unication G-Series P25 Receivers

In this Scanner Master Vlog learn more about the Unication Pager-Receivers. A rugged mini-handheld receiver that solves the problem of APCO P25 digital simulcast distortion. Monitor conventional channels as well as digital trunking.

Links
Unication Software –
http://www.unicationusa.com/downloads-new
Get a Unication Receivers – https://www.scannermaster.com/Unication_Pagers_s/779.htm

Basic Scanner Types

There are basically 3 different types of scanners, “Basic” “Digital” and “ZIP Code”. Which one is best for you depends on the systems used in your area. There are 2 basic formats of scanners, handheld and desktop/mobile.

What we call “Basic” scanners are those inexpensive scanners that usually have analog reception only and do not handle any type of trunking systems. Current “Basic” scanners include the Uniden BC75XLT, BC125AT and BC365CRS as well as the Whistler WS1010 and WS1025. These scanners are fine in areas that do not use digital or trunking systems, they also work well for aircraft, marine and railroad monitoring.

Digital” scanners have the ability to monitor digital and analog trunking systems (EDACS, Motorola, LTR, P25). Some of these scanners also include “Phase 2” systems, which is a newer form of P25. Some radios also will allow you to monitor ProVoice, DMR or NXDN digital systems.

“ZIP Code” or “Database” type scanners are digital trunking scanners that allow one to select a specific area and import channels from an on-board memory card. These memory cards can be updated when needed. These will work almost anywhere in the country and are ideal for those who travel often.

What scanner is best for you? Call us and we can help you decide. We have access to the world’s largest database of scanner frequencies and can quickly look up your area and let you know which radios would work best for you.

When you do call us we will ask a couple questions, including the location you wish to monitor and what format radio you want. With this information we can make a couple suggestions of scanners that will work in your area.

Most of the time we can suggest a couple different scanners with different feature levels. Conversely if you have your heart set on a specific radio we can tell you whether or not it should work in your area.

Scanner Master to Demo the BearTracker 885 at Dayton!

BearTracker885If you are attending the Dayton Hamvention this year please be sure to visit the Scanner Master booth (Booth 3003 in Building #3) to see the new Uniden BearTracker 885. This is the revolutionary new CB radio with a digital police scanner built-in. Or is it a digital scanner with a built-in CB? Whichever way you look at it, it is a neat radio!

Join Scanner Master’s Rich Barnett and BuTel’s Gommert Buijsen as they demonstrate current radios, accessories and software as well as the new BearTracker 885.

While the BearTracker 885 is not yet available for sale pending FCC approvals, you can see it in person exclusively at the Scanner Master booth!

Hamvention is held Friday, Saturday and Sunday, May 19-21 2017 at the Greene County Fairgrounds in Xenia OH, just north of Dayton.

Join the waiting list for the Uniden BearTracker 885.

Antennas: Get creative!

Scannists are always looking for better antennas. The right anttenna can make the difference between hearing your target or not. It is often said that the antenna is more important than the radio it is connected too. One can spend more money on the antenna system that the radio, it is that important. Even more important that the antenna itself can be the coax that connects it to the radio.

That all being said, sometimes there is a way to improve your antenna situation without breaking the bank. In this spirit let’s look at a couple rules that can be broken creatively to get a decent antenna solution at a reasonable price.

Let’s start at the top. With antennas elevation rules all. The higher it goes the better, well most of the time anyway. Does it have to be mounted on the roof however? It might work quite well in the attic. Attic installations can also save on other matters. You usually don’t need fancy mounting gear for attic antennas, just hang it from a rafter or set it on the floor. Antennas in the attic are well protected from the weather and you can do installations in the rain without getting wet.

If you live in an HOA then you might not be allowed rooftop antennas anyway so the attic might be the only way to go. It is not without its problems however. If you have a metal roof or other metallic structures above they would be a problem. Watch for metal backed insulation sheeting, HVAC hoses and other obstructions.

If you live in rental housing or a condo you might not even have the ability to use attic antennas at all. If this is the case then you are stuck with inside antennas. There are a couple things you still could do. Can you mount an antenna on a balcony or patio? How about putting a mobile magnet mount antenna on a refrigerator or air conditioner? Hang a rooftop type antenna from the ceiling or mount on the balcony? There are a lot of different things you can do when limited by space, rules or conditions.

When mounting an antenna on the roof or in the attic be sure to use quality feedline (coax). For scanners either 50 or 75 ohm coax works fine. Avoid the use of adapters as much as possible and try to use the shortest amount of coax as possible. Having 30 feet of coax coiled up in a corner will reduce the effectiveness of the antenna dramatically.

As always, if there are more questions you can ask your friendly (well sometimes grouchy) scanner expert here at ScannerMaster!

Sentinel, Sentinel: What’s the difference?

Owners of Uniden ZIP Code scanners can use the free Sentinel software to do database and firmware updates as well as create and edit Favorites Lists. While they look and feel very much the same, the versions of Sentinel for the HomePatrols is different than that for the BCD436HP and BCD536HP.

The HomePatrol Sentinel works for both the original HomePatrol 1 and the newer HomePatrol 2. When installed on your Windows computer it will have a brown shield icon on the desktop.

The BCDx36HP Sentinel works for both the BCD436HP handheld and the BCD536HP desktop/mobile scanners and has a green shield icon on the desktop.

You can easily share Favorites Lists between HP-1’s and HP-2’s as well as between 436’s and 536’s. In order to share Favorites Lists between HomePatrol’s and “x36’s” you need to export from one and import it to the other.

If you have both types of radios you will need to install both versions of Sentinel. Even though they look and feel the same they cannot handle the other radio types. There is no additional learning curve but there are a few terminology differences. For example, in the HomePatrol Sentinel the menu used to read or write to the radio is called “HomePatrol” while the x36 version it is “Scanner”.

Trunking System Types Glossary

Earlier we discussed the differences between Type 1 & 2 and Phase 1 & 2 trunking systems. This week we will discuss some other formats of trunking. I choose to use the easier to understand mnemonics of 1 and 2 rather than the more correct I and II for some of these systems. These mnemonics are often interchanged.

“Motorola” trunking systems include Type 1, Type 2 and Type 2i systems. The original Type 1 systems used a 3600 baud control data signal and a Fleets/Subfleet programming style. In time it was found to be too limiting, it restricted the number of subfleets and radios that could be accommodated within the Fleets. Motorola developed what was called Type 2 trunking that used a similar 3600 baud control data signal but removed the restrictions about Fleets and Subflleets and removed many of the limits on radios. Type 2 systems could have more than 65,000 individual radio ID’s and thousands of Talkgroups.

Some Type 1 systems were upgraded, either to Type 2 or to a hybrid system that allowed both Type 1 and Type 2 radios, this was commonly referred to as Type 2i. A later version of Type 2 trunking, called APCO P16, used the same Type 2 control data but allowed either analog or digital modulation.

APCO P25, as we discussed last week, is an all-digital format sold by several manufacturers, including Motorola, Harris and others. The format was developed by and for APCO and is licensed from them. The system was designed to be interoperable between the several vendors but often they add features that only they can provide so as to rope in customers to continue buying their radios instead of radios from other companies. One way to tell a Motorola designed system apart is by the control channels. On Motorola systems the Control Channel rarely changes and there are only 2 to 4 channels that they would rotate to if one becomes unavailable. Harris designed systems can use any of the channels for control data and some of these rotate the control data regularly.

P25 voice is also commonly used on conventional (non-trunked) channels as well.

There are two main types of P-25; Phase 1 and Phase 2 (or Phase I and II). Phase 1 allows a single conversation on a voice channel while Phase 2, a form of TDMA, allows 2 on each channel, effectively doubling the capacity of the system.

Most scanners these days only require the current Control Data channel for many of the P25 and Motorola trunking systems to track them.

EDACS is a trunking system originally sold by General Electric as a competitor with Motorola Type 1 and later Type 2 systems. This comes in 2 different types, the 9600 Baud control data commonly used on 800 MHz. systems and 4800 baud control data mostly used on UHF and 900 MHz. EDACS systems can use either analog voice or digital voice, called ProVoice. While any trunking scanner can handle analog EDACS systems only certain Uniden scanners (BCD325P2, BCD996P2, BCD436HP and BCD536HP) scanners can monitor ProVoice operations and these require the ProVoice paid upgrade.

EDACS is commonly used for public safety and less often in business applications. It shares many features with the Motorola trunking formats but is not compatible with it. It can be used as Single Site, Simulcast or Networked or some combination of these.

After several years GE sold the EDACS product line and it bounced around to several companies before landing at Harris Communications. Since EDACS is no longer sold or supported by Harris many of the systems have been shut down or converted to other formats. At some point EDACS systems will all be shut down as parts become unavailable for repairs.

To program an EDACS system into a scanner one needs to put the channels in their proper assigned slots. This is called the “LCN” (Logical Channel Number). This is because the radio only sends the channel number, it is up to the scanner or other radio to match this with the actual frequency.

LTR (Logic Trunked Radio) is a popular format for business users and occasionally used for public safety. This format does not use a dedicated control channel like Motorola, EDACS or P25 systems do. Instead data is sent piggybacked onto the regular traffic on the channel advising specific radios to go to a channel for a message. While this allows all channels to be used for voice messages it is not as robust as other systems so is not often used for police and fire use.

One can tell is an LTR system is in us, there is a characteristic repeater key-up on most channels. This is sending data to radios assigned to that channel as it’s “Home Channel”. Most trunking scanners can handle LTR systems, the trick is determining the LCN slots properly.

DMR/TRBO/NXDN systems can be either conventional or trunked. Some systems can be trunked with a single channel, using sub-audible codes to separate the groups. These systems use TDMA for voice traffic so multiple conversations can be carried on one channel.

While used mostly for business activities these systems occasionally are used for public safety, especially in the SE states.

MotoTRBO is a brand name used by Motorola for it’s DRM offering. While there are slight differences a DMR scanner works fine for unencrypted TRBO systems.
DMR is available on certain Uniden and Whistler scanners.

NXDN trunking is very similar to DMR but just different enough to require a different mode. As of this writing (Spring 2017) NXDN was only available on the TRX-1 and TRX-2 scanners by Whistler.

Type 1, Type 2, Phase 1, Phase 2, what’s the difference?

There is often confusion between different types of trunked systems. One of the most confusing things is the names of some systems. We get calls and letters all the time asking about Phase 2 and Type 2 systems and whether a particular scanner will work on them. They are different and the difference will determine if your scanner will work with it.

TYPE 2 (more accurately but less often written as TYPE II) systems are older Motorola trunking systems that use 3600 baud control data channels. These are commonly referred to as just “Motorola” systems when programming scanners. These were an evolution from the original Type 1 and Type 2i systems. The difference between Type 1, 2i and 2 systems is the way talkgroups are developed. Type 1 systems use a Fleet/Subfleet system that resulted in limited flexibility to assign talkgroups. Most of these systems have been shut down or updated and very few remain in use. Type 2 systems had a different method of assigning talkgroups and allowed greater flexibility. Some systems were called Type 2i, and were a hybrid between Type 1 and Type 2 systems.

Newer Type 2 systems, referred to as APCO P16 systems, allowed either digital, analog or both forms of modulation. There are still many of these systems in use all over the country.

PHASE 1 and PHASE 2 (more accurately referred to as Phase I and Phase II) systems are totally different than Type 1 or Type 2 systems. Phase 1 and 2 systems are forms of APCO P-25 digital systems that use 9600 baud control data channels and all digital modulation. Phase I systems have a single voice path per frequency while Phase II allows 2 voice paths per frequency, effectively doubling the amount of traffic a set number of channels can handle.

It gets even more confusing when programming some radios. Some scanner program the Type 2 and Phase 1 or 2 systems with the same system type, others have different selections. On the user end, most Motorola P25 (Phase 1 or 2) radios are also capable of being used on the older Type 2 systems.

Next week we will look at some of the other trunking systems like EDACS, LTR and TRBO.

When the data isn’t right: How to get your database scanner working.

So you went out and bought one of these fancy new database scanner like the HomePatrol, BCD436/536 or a Whistler TRX and set it up. The problem though is that you are not hearing your local channel that you expected. There are a couple things to try. The first is to double check that you have the location and Service Types set properly. If these are correct, did you accidentally lockout (“Avoid”) the Channel, Department or System?

If you have ruled out these issues take a look at the RadioReference Database at RadioReference.com. This is where the frequency information comes from. If the channel is listed there but not included in your radio then you need to update the database on your radio. Make sure you have installed Sentinel (Uniden) or EZ-Scan (Whistler) and run the update procedure for these scanners. After updating the database make sure you copy (“Write”) it to your radio and try it again.

If you find that the channel is not listed in the RadioReference database then you will have to do some detective work. If you know what the frequency or talkgroup is then be sure to submit it to RadioReference so it can be added or corrected in the database. All you need is a RadioReference user name and password, either a free or paid membership will work. In the meantime it can be added to a Favorites List or Scanlist via the software.

If you do not know what the channel’s frequency or talkgroup is then you will need to do a little more work. If you know they use a trunking system then create a Favorites List and set it to Trunked Search (if on a Uniden). If you have a Whistler then create a ScanList with that system and add a Wildcard to it. This allows you to listen to all activity on the system and when you hear the traffic you want make sure you note the talkgroup number for future reference. You can submit that talkgroup number to RadioReference to update the database and also add it directly to the Favorites List or ScanList with the appropriate name.

On conventional (non-trunked) systems you can do a couple things. First off, check the FCC license for the agency you want to listen to. Most of the time you can do this from the RadioReference database page, just click on the call sign. Since the RadioReference Database only contains information that is verified a new channel might be listed on the license but not included in the main database since no one has reported it as verified yet.

If the channel you seek is not listed there, check licenses for nearby communities, the local County or a regional dispatch center. The actual license might be held by another agency that does dispatch for your town.

Still cannot find it? Now it is time to get serious! Your scanner has a “Search” function. Learn how to set up a Limit Search. Check the most common scanner bands used in your area and set up a search for that band. Lockout the channels as you hear them if they are not your local agency, checking the RadioReference Database as you find them.

Regardless of how you find them be sure to share the knowledge. Submit your finds to the RadioReference Database system so that others in your area can listen in and so that future versions of the database include it. Remember that the database is updated weekly, usually Sunday or Monday. Submissions might take a little while to get processed however so wait to the following week after you receive the notification that your submission has been worked.