Hosting a stream

One of the most popular ways to listen to the local scanner action these days is via a live-streaming service over the Internet. By far the largest source for this is Broadcastify.Com. While this is a great place to listen, it is dependent on someone hosting a scanner for the area you want to listen to. If no one does you can do it yourself. Here is what you need to set up your own feed:

Step 1:    Make sure there is no feed already covering the traffic you wish to stream. If there already is one look at the noted for that feed and see if there is something different that you will do.

Step 2:    If you are not already a RadioReference or Broadcastify member (with user name and password) set up an account. You can set up a free account, paid accounts offer great benefits but are not needed to host a feed. If you are already a member skip this and go to Step 3.

Step 3:    Go to the Broadcastify site and submit a Feed application. They need your information, the channels you plan to stream and some other details. Once you submit your application it takes a few days (usually) for a response, and if approved they provide a code that is entered in your feed software to enable it.

Step 4:    Set up the hardware. This is the computer that you are going to use and the radio itself. You will need an audio cable to connect the computer and radio. If you are using a Uniden scanner you can also connect a USB or serial cable so allow channel tags to be sent along with the radio traffic. See below for the best scanners to be used for feeds.

Step 5:    Set up the software. The software is free from Broadcastify, you can download it there. It is pretty simple to install and set up, print out the instructions that come with it and follow them. If you follow them correctly it will work great!

Step 6:    Adjust the levels. Once your feed is live listen to it and make sure the audio levels are set properly. If the channels you set up are not very active try programming in the local weather channel for a few minutes to use to set the levels properly. Once you have the levels set where they sound best be sure to note the settings in case you need to move something later. Don’t forget to get rid of the weather channel!

What is the best radio for a feed? Well, it is the radio you have that will listen to the traffic you want to stream. Remember, once you commit to hosting a stream that radio must be dedicated to that stream 24/7.

If the radio you use does not have a record jack then you need to set the volume and leave it where it is. Be sure to mark the level with a dab of White-Out in case it gets moved.

For feeds the Uniden BCD15X (analog) and BCD996P2 (digital) are favored by many streamers since they are reasonably priced and have a record jack on the back. The Record jack is ideal for feeds, as the sound level is not affected by the volume control. You set the sound level with the computer’s sound controls and you can use the scanner volume to allow you to listen to the scanner locally without affecting the feed volume. They also support sending channel tags so the listener can see the channel names.

Streaming hints and tricks:

No one likes to hear static, noise etc. Make sure you monitor your stream to be sure that it doesn’t lock up on noise or interference. Make sure the audio levels are good and that the feed sounds good.

How many channels can I stream? The best answer is less is more. If you have a lot of channels or a bunch of real busy ones then the scanner is going to be busy all the time and some channels are going to be missed. Some really busy feeds (like Chicago PD) have just a single channel that is active almost continuously.

What kinds of channels can I stream? These rules are listed in the Terms of Service for the streaming service. Broadcastify has rules against certain tactical or sensitive traffic. Make sure none of the channels you have include the prohibited traffic.

Can I stream 2 radios at the same time? Yes! Set up one radio to the left channel and the other to the right. Possible scenarios are police on one and fire on the other. Make sure you note this in the feed description!

What do I do if the agency doesn’t want me to stream them? Well, that is up to you. Streaming is legal and the agency cannot force you to stop streaming their traffic. They can however add encryption, then it will not be able to be heard at all by anyone.

Broadcastify has a complete set of rules and procedures on it’s page at Broadcastify.com. If you use a different service be sure to read their rules before setting up your feed.

All those weird ports on the back of the scanner

Modern scanners have a plethora of various ports, jacks and sockets on them. Here is a look at some of them.

Taking a look at the rear panel of the BCD536HP scanner there are 6 different ports on it. From left to right they are:

  • BNC antenna jack
  • External Speaker Jack
  • USB Port (used for WiFi unit only on the 536)
  • GPS Serial Port
  • 3-pin power port
  • Coaxial power port

Other common ports on scanners include:

  • USB programming port
  • Record jack
  • Headphone jack
  • Various serial ports.

Let’s look at each port and what it is used for: (*Bonus! See below for an explanation of the weird hole smack in the middle…)

Antenna Jack:  Of course this is used to connect an antenna to the radio. Most scanners these days use BNC, the little push and turn job you see in the picture. Some handled scanners use the smaller SMA connector. Some older scanners had Motorola or even SO139 connectors and some had both an external connector and an internal threaded connector with a hole in the case to insert it.

External Speaker:  These are used to plug in an external speaker and are different than headphone jacks. Speaker Jacks do not limit the volume like a headphone jack will. When you plug in a speaker into the external speaker jack the inside speaker is disconnected.

Headphone Jack:  The Headphone jack has a limiting circuit to protect from overly loud sound that can damage your hearing. Otherwise it works much like the external speaker jack. Headphone jacks are usually in the front panel of desktop scanners while speaker jacks are usually on the rear. Handheld scanners usually just have a headphone jack on the top.

Record Jack:  The Record Jack allows one to pull audio from the scanner at a constant level that is not affected by the volume control. This is important when the radio is used as a source for recording or streaming. Some older RadioShack scanners and some current Uniden scanners have record jacks.

GPS Serial Port:  Unique to Uniden scanners, the DB-9 Serial port (male) is used mostly to connect a GPS receiver to allow location based scanning. It can also be used to program or control the scanner with the properly constructed cables. Do not confuse this with the female DB-9 port used for programming on older scanners like the BC780XLT or the BC898T

USB Programming port:  Most scanners these days use a USB-Mini port on the front or side to program and control the scanner. On many handheld scanners these ports are also used to charge the batteries and power the radio. On the BCD325P2 a special cable is used to connect a GPS to this port.

Other serial ports:  Some older scanners use different type serial ports. Older Unidens (like the “XT” series) use a unique 4-pin square connector for programming and connection of the RH-96 remote head. HP-1 and HP-2 scanners use that same port style for connecting to a GPS. Older design RadioShack/GRE/Whistler scanners use a jack that is just like a headphone jack for serial port connections.

Coaxial Power Port:  Most desktop/mobile scanners have a coaxial power port to provide 12 VDC to the scanner. There are 2 different jacks in common use. The majority of Uniden mobile and desktop scanners use a “Type M” male jack while most recent RadioShack, GRE and Whistler mobiles use a “Type T” female jack. Both use center-pin positive. Some older handheld scanners use smaller coaxial power ports but newer portable scanners usually use the USB port for charging and external power.

3-pin power port:  This is another unique to Uniden port, similar to the power port used on some of their CB products. On Uniden scanners there are the regular black and red wires for power and a third orange wire used to control the brightness of the display when connected to the lighting circuits of the car.

Discriminator Jack:  This is probably the most popular jack that doesn’t come on scanners. Discriminator audio is used to provide an unfiltered audio source mostly for data decoding. This type of decoding usually does not work from the record or speaker jacks due to the filtering circuitry in the radio. Scanners usually do not come with jacks for this but it is often added on by advanced scanner hobbyists to allow data decoding.

 

Bonus Round

See that threaded hole smack in the middle of the back panel in the picture at the top of the page? Most Uniden base/mobile scanners have that. It is used to allow a rear bracket to stabilize the radio under the dashboard. It is not mentioned in the owner’s manuals but is shown in the diagrams.

FRS/GMRS/MURS/CB: The Personal Radio Services

Anyone can use one of several types of two-way radios, most of which do not require a license. From something the kids can play with to serious business uses there are a bunch of different types of varying quality and usefulness. These are called CB, FRS, MURS and GMRS. Only GMRS requires a license, the others do not. Each of the four services have different intended functions.

  • FRS: Family Radio Service (low power, short range, intended for families and individuals)
  • GMRS: General Mobile Radio Service (high power, longer range, intended for families)
  • MURS: Multiple Use Radio Service (mid-power, medium range, intended for business)
  • CB: Citizen’s Band Radio Service (low power mobile)

You ever go into Wal-Mart or Best Buy and see those cheap little two-way radios encased in one of the most devious inventions of man-kind (Bubble Packs)? They boast wild range figures (“35 mile Range!”) and are made by many different companies like Motorola, Midland and Cobra. These are called “FRS Radios” (Family Radio Service). FRS radios are restricted to ½ watt, non-removable antennas and are intended for short-range person-to-person communications. While titled as the Family Radio Service they are commonly used by businesses and government organizations. In my neighborhood I hear construction crews, hunters, the local school and the golf course maintainers on FRS channels. Just about everything but families… There are few restrictions on what you can use it for so business and personal communications are allowed.

FRS is actually pretty interesting to listen to in many cases. While a lot of the traffic is inane nonsense, like kids wearing out the noisemaking alert beep button, occasionally there is some interesting stuff to listen to. I live in a fairly isolated area 20 miles from the nearest town. There is construction going on and the crews use several FRS channels to coordinate activities. There is a school in the area that uses FRS radios too. The golf course guys use FRS when performing maintenance or to corral loose duffers. Local landscapers use FRS as well.

Listening to FRS channels at the mall or around amusement parks etc. can also be fun. The stores and shops often use FRS radios for clerks and stockers, customers use them to keep in touch with their family.

A lot of the FRS channels are shared with GMRS, so listening to one set of frequencies you may hear both services.

GMRS is a little different than FRS. Since a license is required and power levels are higher they tend to be used in a more formal matter. FRS also allows repeaters so you may hear traffic from all over the area. GMRS is often used by REACT and other volunteers as well as family businesses and often for just idle chit-chat and radio clubs. Sometimes it sounds a lot like ham radio.

MURS can be very interesting. It is on VHF and allows higher power than FRS but in many other aspects it is very similar. Like FRS there are few restrictions on what you can use it for. Since the radios tend to be a little more expensive MURS channels tend to be more business oriented.

CB these days is mostly a wasteland of unintelligible noise. It is still popular with the highway crowd but between high-power illegal amplifiers, over-driven power echo-mics and other noisemakers it is no longer a viable communications tool. It can be interesting to listen to however!

If you put these frequencies in your scanner you may find some interesting communications. You might also be bored silly but you won’t know until you try it.

General Mobile Radio Service (GMRS)

  • Freq (MHz)              Remarks                  
  • 462.5500                 Repeater Output/Simplex    (Repeats 467.5500)
  • 462.5750                 Repeater Output/Simplex    (Repeats 467.5750)
  • 462.6000                 Repeater Output/Simplex    (Repeats 467.6000)
  • 462.6250                 Repeater Output/Simplex    (Repeats 467.6250)
  • 462.6500                 Repeater Output/Simplex    (Repeats 467.6500)
  • 462.6750                 Repeater Output/Simplex    (Repeats 467.6750)
  • 462.7000                 Repeater Output/Simplex    (Repeats 467.7000)
  • 462.7250                 Repeater Output/Simplex    (Repeats 467.7250)
  • 462.5625                 Simplex (5 watts)
  • 462.5875                 Simplex (5 watts)
  • 462.6125                 Simplex (5 watts)
  • 462.6375                 Simplex (5 watts)
  • 462.6625                 Simplex (5 watts)
  • 462.6875                 Simplex (5 watts)
  • 462.7125                 Simplex (5 watts)

Family Radio Service (FRS)

  • Freq (MHz)              Ch #         
  • 462.5625                 1
  • 462.5875                 2
  • 462.6125                 3
  • 462.6375                 4
  • 462.6625                 5
  • 462.6875                 6
  • 462.7125                 7
  • 467.5625                 8
  • 467.5875                 9
  • 467.6125                 10
  • 467.6375                 11
  • 467.6625                 12
  • 467.6875                 13
  • 467.7125                 14
  • 462.5500                 15 (Shared with GMRS)
  • 462.5750                 16 (Shared with GMRS)
  • 462.6000                 17 (Shared with GMRS)
  • 462.6250                 18 (Shared with GMRS)
  • 462.6500                 19 (Shared with GMRS)
  • 462.6750                 20 (Shared with GMRS)
  • 462.7000                 21 (Shared with GMRS)
  • 462.7250                 22 (Shared with GMRS)

Multiple Use Radio Service (MURS)

  • Freq (MHz)                                                 
  • 151.8200
  • 151.8800
  • 151.9400
  • 154.5700
  • 154.6000

Citizens Band (CB)           

  • Freq         Ch #          Freq         Ch #         
  • 26.965    1                27.215    21
  • 26.975    2                27.225    22
  • 26.985    3                27.255    23
  • 27.005    4                27.235    24
  • 27.015    5                27.245    25
  • 27.025    6                27.265    26
  • 27.035    7                27.275    27
  • 27.055    8                27.285    28
  • 27.065    9                27.295    29
  • 27.075    10             27.305    30
  • 27.085    11             27.315    31
  • 27.105    12             27.325    32
  • 27.115    13             27.335    33
  • 27.125    14             27.345    34
  • 27.135    15             27.355    35
  • 27.155    16             27.365    36
  • 27.165    17             27.375    37
  • 27.175    18             27.385    38
  • 27.185    19             27.395    39
  • 27.205    20             27.405    40

WiFi on BCD536HP. How does it work?  What you can and can’t do with it.

The Uniden Bearcat BCD536HP is the only scanner that has the capability of being directly controlled by WiFi. By using the included WiFi dongle one can connect a smart phone or tablet to the scanner and listen to and control the scanner with the device. There are some other uses for the WiFi dongle as well.

Uniden has provided free “Siren” software (available for free via the Apple iTunes store or Google Play Store) to allow you to use your smart device as a scanner controller. You can even use this as a remote head for the scanner if mounted in a vehicle or to listen to your scanner from the patio or another room of the house for a scanner installed in the home. Some third party software allows you to use the WiFi feature to connect the canner to the computer without the need to plug in a cable.

There are a few things that the WiFi dongle will not work for, this includes database and firmware updates and other programming.

The Wifi dongle is designed specifically to work with your home or office WiFi network. While we have read of people using it for remote access this requires such networking tools as VPN, if you know how that works you probably can figure it out. Sorry, we cannot help with notworking issues like this!

To use the WiFi feature you need to understand the two modes involved; Infrastructure and Access Point.

Infrastructure Mode allows your scanner to connect to your home or office WiFi. This then allows you to connect to the scanner via third-party software like ProScan or RadioFeed or to the Siren application.

To get to Infrastructure Mode use the following steps:

Press Menu then select WiFi Setup>Select WiFI Mode>Infrastructure Mode

The radio will look for local access points and list them. When it displays the list select your router’s SSID name.

Then enter your password for the WiFi access point. This is the same password you would use for setting up any other WiFi device on your network. To enter the password you scroll thru the letters and use the 4 and 6 buttons to move the curser.

Access Point Mode allows you to connect you scanner to a smart phone or tablet (iOS or Android) using the free Siren software. You would use this when you are not in range of your WiFi system, such as when the radio is mounted in a vehicle. This allows you to use a phone or tablet as sort of a remote control head for the scanner.

In Access Point Mode the 536 acts as an Access Point and provides an SSID which you can change or leave at the default. You then connect your phone or tablet to that WiFi SSID and enter in the IP address in the Settings of the device. The IP address can be found in the WiFi settings on the scanner.

Siren is the free app available at the Apple iTunes Store for iPhones, iPads and iPod Touch’s. It is also available for Android devices at the Google Play Store.

Siren is a neat way to use your 536 scanner but there are limits to it. It will only work with the 536, and it has limited abilities for control. It can set the range, select Quick Keys, set the squelch and start and reply the recording features but that is pretty much all she wrote. There is also a 2-3 second delay in hearing the audio compared to the radio itself.

The WiFi feature on the 546 is unique and useful as long as you know its limits.

The BearTracker 885: Is it a scanner or not?

BearTracker885
Uniden recently released its new BearTracker 885 CB-Scanner combination. Here are a few things to know about it:

1) It has a LIMITED FUNCTION scanner.

The 885 has a specially designed scanner built in that will receive local police, fire, EMS and Highway Department channels based on your location. The radio will tell you whether the channel is Police, Fire etc. but it does not indicate the agency or channel name. You can hear the traffic, the display will tell you that it is police or whatever, but it won’t tell you whether it is Mayberry or the Highway Patrol.

2) You can UPDATE but not program the scanner part.

The 885 has a free software program that simply updates the database the radio uses to hear local traffic. You cannot add/delete or modify channels. To update the radio is fairly simple, take out the full-size SD card, insert it into an SD-Card reader attached to your computer and run the updater program. (The radio does not come with an SD-Card reader, if your computer doesn’t have one you can get them for a few dollars.) The updater software pulls the latest data from the RadioReference database and loads it onto the SD-Card. The database is updated weekly but you only need to bother updating the database once or twice a year.

3) How does the 885 know where I am?

The 885 comes with a GPS receiver. The small receiver is connected to the GPS by an included cable, just put the little box in view of the sky (on the dashboard etc.) and plug it in. If this won’t work for you then you can manually enter in the location from the front panel controls of the radio. When using the GPS the radio’s location is updated regularly and the scanner part will reload itself with the local channels.

4) What about the CB?

The 885 is a basic 40 channel CB. It does not do SSB but it has the typical CB features needed to communicate or listen to other vehicles so equipped. It can also be used as a PA (PA Speaker not included) or as a weather receiver.

5) Is it legal?

We are not lawyers and do not offer legal advice. That said, CB’s are legal for use in the USA and Canada without a license. As far as the scanner goes check with your state and local authorities about whether a scanner is allowed in a vehicle. Laws may vary for commercial vehicles. Since this device has no radar detector it is not prohibited from commercial vehicles for that reason.

If you are interested in scanning specific agencies or want a scanner that allows you more choice then perhaps the 885 is not the radio for you. If you are looking for a CB and like the idea of hearing local emergency scanner traffic then this radio could be ideal.

Download Uniden BearTracker 885 Flyer

Force Write full Database (HP1, HP2 BCD436 and BCD536)

When updating a HP series (HomePatrol 1 and 2, BCD436HP and BCD536HP) scanner one of the update is the database that the ZIP Code feature relies on. If the database has old or incorrect data then it can affect whether you will be able to hear your target. If you update the database on a regular basis you can help ensure that you will hear what you want.

When you update the database within Sentinel (the free software provided by Uniden to support these scanners) it doesn’t actually update the database on the scanner itself. You have to “Force-Write” the database to the scanner. This is easy; after you “Update Master HPDB” in the Update menu just click the “Force-Write Full Database” button on the Write to Scanner (or Write to HomePatrol) item in the Scanner (or HomePatrol) menu.

This ensures that the Master HomePatrol database on your scanner is up to date.

DMR, ProVoice and Ultimate Updates for Uniden Scanners.

ScannerMaster offers a service to install the various paid updates for Uniden HomePatrol, x36 and P2 series scanners. These updates include the HomePatrol Ultimate Update (for HomePatrol 1 and 2 scanners) as well as the ProVoice and DMR/TRBO updates for the BCD436HP, BCD536HP, BCD996P2 and BCD325P2 scanners.

If you buy one of these scanners from ScannerMaster we offer a service to install these options for you before we ship the scanner. You can also send the scanner to us to perform the update, we then send the radio back to you.

Sometimes however it is not practical to send the radio to us. For US and Canadian customers it is pretty simple to buy the update directly from Uniden and install it yourself. For customers in other countries however it is a different story. Uniden can only accept credit cards from US and Canadian addresses. If you live in other countries then Uniden cannot accept your credit card for payment for these updates. They will refer you to a third party like ScannerMaster to obtain your updates.

ScannerMaster can accept credit cards from most countries. As long as the card works on our payment system we can provide you with the secret code to unlock the update for your radio. There are a couple things you will need to do to make this all work out:

First you need to update the FIRMWARE for your scanner. This is so important that if you don’t do it the paid updates just will not work! On the HomePatrol and x36 scanners it is done thru the Sentinel software, on the 325 and 996P2 radios it is done thru a separate (free) program available from Uniden’s website.

Once you have done the Firmware Updates then you need to obtain the “ESN” (Electronic Serial Number” from your scanner along with the “SUM” code. Here are the procedures for this:

HomePatrol-1 and HomePatrol-2:

  • Press Menu
  • Press Advanced Menu
  • Press the down arrow to get to the second page of items
  • Press the Version Information Button.

The ESN is listed and starts with 36 for the HP-1 and 37 for the HP-2. The SUM Code is the last 3 digits past the second dash. The ESN will look something like 36327-0040012345-123, the SUM code is the “123” part.

BCD436HP, BCD536HP, BCD325Ps and BCD996P2:

  • Press Menu
  • Select Settings.
  • (If you do NOT see “Upgrade” as an item in the list go back and update the firmware and start over!)
  • Select See Scanner Information
  • Select Firmware Version
  • The ESN will be listed as “SN37……”
  • The SUM Code will be a 3-digit letter/number combination.
  • We need both the ESN and the SUM Code. Don’t worry about the M-VER code.

We need the complete ESN and the SUM Code as well as the model of radio you have. With this info we can obtain the one-time code that unlocks the feature you want and send that code to you. You then go to the Upgrade menu on your scanner and enter it using the rotary knob to select the numbers. Once the code is properly added the radio will think it over for a minute or so and then announce that it was successful.

Once properly updated the code will stay working on the radio and will not need to be reinstalled. The code will only work for the radio it was obtained and if you dispose of the radio there is no way to transfer the code or feature to another radio.

Weird Funkiness with scanners: 536 Cuts out

We here at ScannerMaster get calls from customers often to explain some sort of weirdness happening with their scanner. Usually we can figure it out pretty quick but once in awhile we get stumped. When we get stumped it sticks in our craw for a while until we have an epiphany and figure it out. We had one just like that earlier this week.

A customer called and his brand new BCD536HP was acting all ornery. Every couple of seconds it would stop hearing and the signal strength meter would fluctuate. Most of the time this is caused by the Priority or CloseCall features. We determined it was neither of these but still couldn’t figure out what it was.

Here is why we were looking at these features:

Priority, when enabled, will check specified channels every couple of seconds for activity on it. If there is activity it will divert the radio from what is was doing to listen to the Priority channel.

CloseCall will check for strong signals in the area and if detected will divert the radio to the frequency the CloseCall feature detected. If the feature is set to CloseCall Priority then it will cause the radio to stop hearing a channel for a bit, just like the customer complained.

So when we made sure both Priority and CloseCall were off we were flummoxed. Well, I was flummoxed; he was frustrated. I am sure there were some other words starting with “F” being bandied about as well.

I started going thru the menus on the radio in the office (We have one of just about everything here at ScannerMaster) and eventually dug thru all the menus and submenus. Eventually we found the culprit: The Weather Alternate Priority. Somehow the customer got this turned on. As soon as we turned it off the radio worked great again! We had one happy customer and a relieved representative.

The Weather Alert Priority tells the radio to check the weather channels every few seconds and if it detects the standard 1050 Hz. tone used to signify a Weather Alert it will divert the radio to that alert.

New scanners have a ton of neat features but sometimes they can be too smart. Some of these features can cause aggravation when that feature is not needed.

Software UPDATE: ARCXT Software V.2.1 Build 3

BuTel ARCXT Software update is now available
Download here ARCXT Basic / ARCXT PRO

BuTelChanges in 2.1 build 3:

  • added support for DMR/Mototrbo systems
  • added talk group filters to RR import
  • added service type filters to RR import
  • fixed error message in RR import
  • add print group quick keys option
  • added Color code settings to DL/DPL

DMR/ProVoice firmware update information 

Note:
Owners of the BCD325P2 and BCD996P2 must update the scanner firmware in order to use the new ARCXT update.  This is only for P2 models and does not effect XT models.

BCD325P2 Firmware Updates
BCD996P2 Firmware Updates

Uniden Location Based scanner hints

Uniden’s line of Location Based scanners allow one to enter their location (usually by ZIP Code) to load local channels without needing to know frequencies, systems, talkgroups and other technobabble. There are a couple things to remember and a couple byproducts that can make life your scanner easier. These scanners include the HomePatrol 1 & 2, as well as the BCD436HP and BCD536HP.

First the good stuff! Did you know that you do not need the scanner itself to do most updates, including firmware? That’s right! If the radio is mounted in the car (especially for the BCD536HP) just remove the memory card and connect it to your computer using a card reader. Since these are “Mini SD-Cards” you will need a card reader that will read them or one that works with standard SD Cards and a Mini SD-Card adapter. Just plug the SD card into the card reader and then the reader into the computer and run Sentinel just like you would if the radio was plugged in. (When doing the Extreme, DMR or ProVoice Updates you must do them on the radio itself as the code is installed from the keypad.)

SD Card readers are inexpensive and some computers have SD-Card readers built in. Remember that the Mini SD-Card requires the Full-Size adapter since most computer slots and card readers do not accommodate the Mini SD-Card directly. While Uniden doesn’t supply the adapter card with the radios they are easy to find and come with Mini SD-Cards you buy in the store. This leads us to the next part:

Get a spare card!

Why have just one SD-Card for your scanner when you can have several? SD-Cards are cheap these days. You can buy spare or replacement cards anywhere (including ScannerMaster) and keep them in case you have difficulties. One problem with SD-Card based scanners is that the cards can be corrupted if the power is removed while the radio is on. Since the radio has to write some closing data to the card, one must turn the radio off before removing power or the batteries. Sometimes a voltage spike could cause this as well.

With a spare programmed SD-Card you can be ready if you have a problem. I have found that having a spare seems to prevent the need for it; the only time I corrupted a card was when I was on the road with no computer. I have since always carried a programmed spare card and never had a corruption issue. Coincidence? I think not!

Update your radio.

Using a card-reader to update the SD-Card in your Uniden Location Based scanner is simple, you can update the firmware, database and Favorites Lists directly on the card itself, plug the card in and the radio will automatically be updated. When you do this the radio’s firmware will be updated the first time you power the radio up with the new or reprogrammed card. The database and any enabled favorites lists will then load.

On the 536 you can just pop the card in and out from the front panel. Be sure to turn the radio off first! On HomePatrol and 436 radios the card is behind the batteries, so to access it remove the batteries, On the 436 slide the small metal retaining clip over and remove the card. To replace the card slide it into the clip, fold it down and slide the clip over again. On the HomePatrol the care pops in a slot, gently press it in a tiny bit to release it. When replacing the card carefully pop it into the slot until it clicks in.

Buy a new card from ScannerMaster!

When we do our Setup and Optimize on a scanner most customers would send the radio in to us, we do the updates etc. and then ship the radio back to the customer. We soon figured out that it would be easier and cheaper for the customer to buy a replacement card, have the card programmed and delivered. This way an expensive radio isn’t being shipped across the country twice, risking damage or loss. You get a new SD-Card, of a type faster and more reliable than that supplied with the radio. If your old card still works then you already have a spare. You save up to 10 days of transit time, don’t have to pay expensive shipping fees. Mailing an SD-Card costs less than $2.00, shipping a radio costs $15-25 each way. We also include the Full-Size adapter!

You can also create SD-Cards yourself with Sentinel. Remember that you need to use the “Clear User Data” menu item on a new card to format it for use on your Uniden radio.

Whistler SD-Card based scanners can be updated to a lesser extent, the DSP and firmware updates must be done thru the radio itself. The mobile Whistler scanners (WS-1095, WS-1098 and TRX-2) come with a full-size SD Card, the portable Whistler scanners use Mini SD Cards. Mini SD-Cards can be used in the mobile radios with the full-size adapter.